Direct factory access to top-tier DIN-rail automatic transfer switches, smart breakers, manual isolators, and power distribution cabinets optimized for Myanmar’s electrical conditions.
Low-voltage power distribution networks across Southeast Asia, particularly in fast-growing regions like Bago (Myanmar), encounter recurring electrical disturbances. Transient overvoltages caused by atmospheric lightning discharges, inductive load switching, and power grid instability represent the single leading cause of premature failure in industrial drives, commercial HVAC units, and residential solar inverters. A Type 2 Surge Protective Device (SPD), also classified as Class II under IEC 61643-11 / EN 61643-11 standards, serves as the primary defense mechanism installed within main and sub-distribution panels.
Unlike Type 1 SPDs designed to handle direct lightning currents with an 10/350 µs waveform, Type 2 SPDs are engineered to suppress indirect lightning surges and induced switching transients characterized by an 8/20 µs current waveform. Positioned downstream from the service entrance (or combined with Type 1+2 units at the main switchboard), a Type 2 surge protector diverts excess surge currents harmlessly to earth while clamping residual transient voltage ($U_p$) below the dielectric withstand capability of protected terminal electronics.
Our Type 2 SPDs utilize high-energy Zinc Oxide ($\text{ZnO}$) varistors sourced from top-tier raw material suppliers. When voltage spikes exceed the Maximum Continuous Operating Voltage ($U_c$), MOV resistance collapses from megohms to milliohms in under 25 nanoseconds, clamping the surge instantly.
Continuous grid overvoltages can drive varistors into thermal runaway. Our integrated internal disconnector mechanically isolates the MOV from the mains before thermal destruction occurs, triggering a visual status indicator (Green = Normal, Red = Replace).
Designed for rapid maintenance on busy industrial sites, the DIN-rail base remains wired while individual cartridge modules can be hot-swapped without de-energizing the entire panel board, minimizing operational downtime.
Zhejiang DVS Electric Co., Ltd. manufactures a full spectrum of AC and DC Type 2 surge protectors designed specifically for electrical distributors, panel builders, and project contractors serving the Bago region.
Configuration: 1P+N, 2P
Nominal Voltage ($U_n$): 230V AC (50/60Hz)
Max Operating Voltage ($U_c$): 275V / 385V / 440V
Discharge Rating ($I_n / I_{max}$): 20kA / 40kA (8/20µs)
Voltage Protection Level ($U_p$): ≤ 1.5 kV
Ideal for residential distribution boxes, light commercial boards, and single-phase motor drives across Bago township.
Configuration: 3P+N (TT / TN-S Grid Systems)
Nominal Voltage ($U_n$): 400V AC 3-Phase
Max Operating Voltage ($U_c$): 385V / 440V AC
Discharge Rating ($I_n / I_{max}$): 20kA / 40kA & 30kA / 60kA
Auxiliary Contact: Remote status signaling optional
Essential for industrial workshops, textile factories, and rice mills in the Bago industrial zone.
Configuration: 2P (Y-PV / Direct), 3P
System Voltage ($U_{cpv}$): 500V, 800V, 1000V, 1200V DC
Discharge Rating ($I_n / I_{max}$): 20kA / 40kA
Compliance: EN 50539-11 / IEC 61643-31
Engineered specifically for solar PV string combiner boxes and central/string inverters in agricultural and off-grid applications.
Application: RS485, Ethernet, CCTV, Telecom
Operating Voltage ($U_c$): 5V, 12V, 24V, 48V DC
Bandwidth: High-frequency low loss
Connector Types: Screw Terminal, RJ45
Protects sensitive telemetry devices, remote terminal units (RTUs), and smart meters from indirect lightning surges.
The geographic and infrastructural profile of Bago Region demands tailored surge protection strategies. Below are the prominent real-world deployment scenarios where our Type 2 SPDs deliver maximum ROI and grid resilience.
Factories along the Yangon–Bago industrial corridor rely heavily on automated looms, rice processing lines, and cold storage units. Power distribution panels in these environments experience intense switching surges from heavy inductive loads and frequent grid transfers. Installing our 3P+N Type 2 SPDs (385V/440V Uc, 40kA Imax) at sub-distribution boards prevents PLC lockups, VFD insulation breakdown, and costly machine downtime.
Throughout rural Bago, off-grid photovoltaic arrays drive agricultural water pumps and community mini-grids. Exposed rooftop and ground-mounted solar panels act as prime targets for induced atmospheric lightning transients during monsoon months. Our DC 1000V Type 2 SPDs installed inside PV combiner boxes safeguard solar charge controllers, battery storage units, and pumping inverters.
Cellular base stations situated on elevated terrain across Bago experience intense thunderstorm activity. Outdoor cabinet power supplies and rectifiers require robust surge immunity. DVS Electric supplies compact DIN-rail Type 2 SPDs with integrated dry-contact microswitches, allowing telecom operators to monitor surge protector health remotely via centralized telemetry networks.
Understanding the local electrical ecosystem is crucial for selecting appropriate SPD parameters. Electrical contractors and importers in Bago face specific challenges driven by climate and grid infrastructure evolution.
The Bago Region records high keraunic activity, averaging 60 to 90 thunderstorm days annually, concentrated heavily between May and October. Cloud-to-ground lightning strikes induce electromagnetic pulses (LEMP) into overhead distribution cables. Unprotected service panels experience voltage transients reaching several kilovolts, destroying un-suppressed electronics within milliseconds.
Due to scheduled load shedding and voltage instabilities across local 230V/400V supply lines, businesses in Bago rely heavily on dual-power automatic transfer switches (ATS), diesel generators, and solar hybrid inverters. Rapid switching between grid power and backup sources generates significant switching surge transients. Choosing an SPD with elevated $U_c$ ratings (e.g., 385V or 440V AC) prevents premature varistor thermal aging caused by temporary overvoltages (TOV).
Use the following technical selection guide to match DVS Type 2 Surge Protector specifications with your installation requirements in Bago.
| Model Series | Network / Voltage | System Type | In / Imax (8/20µs) | Up (Clamping Voltage) | Recommended Backup Protection |
|---|---|---|---|---|---|
| DVS-AC20-275 | 230V AC Single Phase | TT / TN-S (1P+N) | 20kA / 40kA | ≤ 1.3 kV | 32A C-Curve MCB / Fusible Disconnect |
| DVS-AC40-385 | 230V/400V 3-Phase | TT / TN-S / TN-C (3P+N) | 20kA / 40kA | ≤ 1.8 kV | 40A or 63A C-Curve MCB |
| DVS-AC60-440 | 400V Unstable Grid | Heavy Industrial 3P+N | 30kA / 60kA | ≤ 2.0 kV | 63A gL/gG Backup Fuse |
| DVS-PV600V | 600V DC Solar String | PV Array (2-Pole Y) | 20kA / 40kA | ≤ 2.5 kV | Internal Thermal Isolation / DC Fuse |
| DVS-PV1000V | 1000V DC Solar String | Commercial PV (3-Pole) | 20kA / 40kA | ≤ 3.6 kV | 1000V DC Photovoltaic Fuse Holder |
Custom voltage parameters, custom packaging, and branded front-plate labeling available for Bago distributors upon request.
As a leading low-voltage electrical equipment manufacturer headquartered in Wenzhou—China's electrical capital—Zhejiang DVS Electric brings 24 years of manufacturing excellence to importers and contractors across Southeast Asia.
Our dedicated manufacturing base houses automated SMT lines, MOV sorting stations, robotic housing assembly, and laser marking machinery. We maintain full control over quality and production speed.
Every batch of Type 2 surge protectors undergoes 100% calibration and routine verification. Our testing facility generates 8/20 µs current impulses up to 60kA to guarantee varistor clamping voltage accuracy.
We provide full OEM branding, including private-label housing printing, custom retail packaging, bilingual English/Myanmar instruction manuals, and tailored technical specifications to help you build market dominance.
Got questions about importing or installing Type 2 Surge Protectors? Here are technical answers from our engineering team.
Partner directly with Zhejiang DVS Electric Co., Ltd. Get wholesale factory pricing, certified quality, and dedicated engineering support for all your low-voltage protection projects.
Contact Us